Just how to Replace a Bathtub ( Guide).
Just how to Replace a Bathtub ( Guide).
Blog Article
We've stumbled upon this post involving A Step-by-Step Guide to Installing a Bathtub below on the web and figured it made sense to share it with you over here.
Installing a tub isn't specifically brain surgery, however it does call for solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably hard task. If the old tub is readily available, the project can move immediately; if you need to open up a wall to remove the old tub as well as place the new bathtub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will certainly need an assistant to vacate the old bathtub and also embeded in the new one. Make certain you have actually certified on your own for the work and also fit attempting it. Rather than hiring a professional to take over a halfway-completed project, it is better to consider employing one before you begin. Possibilities are you may need a professional plumber to make tube links.
This article will help you install a new tub in your restroom if you have already purchased a new tub and don't need to change the setup of your previous water pipelines.
Your tools and product list ought to comprise the following:
Planning for the Installation
Firstly, the sustaining framework provided with the bathroom ought to be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be fitted in its final placement.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to carrying on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Utilizing both wood boards under its feet, put the tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the bath tub up until the spirit level reads level.
To mount faucets, fit all-time low of the furthest flexible tap adapter to the proper supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the tub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the maker's instruction manual. Tiling and sealing around the bathtub should wait till the bath tub has actually been utilized at least once as this will certainly settle it into its last position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines remain in place in between the tap and also the sink. Protect the tap in position with the producer provided backnut. When the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former type must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, triggering the water to penetrate the wall in between the bath and also the tiling, resulting in difficulties with dampness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and also fittings. They are offered in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched paper or soft rope. Remember to constantly load the bathtub with water prior to sealing, to permit the movement experienced when the tub remains in use. The sealant can split relatively very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily offered on the marketplace. It is advisable to fit the tiles utilizing waterproof or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been introduced to that editorial on How to Install a Bathtub Yourself through an acquaintance on a different site. Are you aware of someone else who is interested in the topic? Why not promote it. I love reading our article about Tools You Need to Install a New Bathtub .
Book Your Service Report this page